If your Roborock S8 making loud noise has become a daily disruption, you're not alone. This premium robot vacuum is designed to operate quietly, so unexpected grinding, rattling, or high-pitched sounds usually indicate a fixable mechanical issue. Before you consider a costly replacement, most noise problems with the S8 can be resolved with simple cleaning and maintenance. This guide walks you through the most common causes and step-by-step solutions to restore your vacuum's whisper-quiet performance.
Common Causes of Loud Noise in the Roborock S8
The Roborock S8 features advanced dual rubber brushes and a powerful suction motor that, when obstructed or worn, can produce alarming sounds. Understanding what's causing the racket helps you target your troubleshooting effectively.
Step-by-Step Troubleshooting Guide
1
Power Off and Inspect the Main Brush: Turn off your S8 completely and flip it over. Remove the main brush cover and extract the dual rubber brushes. Check for tangled hair, string, or debris wrapped around the rollers. Clean thoroughly with the included cleaning tool, paying special attention to the bearings at both ends where hair often accumulates and causes grinding noises.
2
Clean the Side Brush and Its Motor Housing: Remove the single side brush by unscrewing or pulling it off depending on your S8 variant. Clear any wrapped debris from the brush itself, then use a flashlight to inspect the small motor shaft underneath. Built-up hair here forces the motor to strain, producing a high-pitched whining sound during operation.
3
Empty the Dustbin and Check for Blockages: Remove the dustbin completely and empty it. Detach the filter and tap out fine debris. Shine a light through the intake port to spot clogs in the airway path. A blocked airflow forces the motor to work harder, creating excessive suction noise. Also verify the dustbin is seated properly when reinstalled—a poor seal causes whistling sounds.
4
Inspect the Wheels for Debris: Check both the omnidirectional front wheel and the main drive wheels. Pop out the front caster wheel and remove any hair or grit from its axle. For the drive wheels, rotate them manually—they should turn smoothly with consistent resistance. Crunching or clicking indicates trapped debris in the gear mechanisms that requires careful extraction with tweezers.
5
Examine the Mop Pad and Vibration Module: If your S8 Pro Ultra or similar variant includes sonic mopping, a loose or improperly attached mop pad can create rattling against floors. Ensure the pad is correctly mounted and the Velcro is secure. Remove the pad entirely and test the vacuum without it to isolate whether the noise originates from the mopping system.
6
Test and Reset the Unit: After cleaning all components, restart your S8 and run a short cleaning cycle on hard flooring where noise is most audible. If the sound persists, perform a factory reset through the Roborock app (Settings → Device Settings → Factory Reset). This resolves software-related motor control issues that can cause irregular motor sounds.
Warning: Never operate your Roborock S8 with wet brushes or components after cleaning. Moisture entering the motor housing can cause electrical damage and void your warranty. Allow all parts to air dry completely before reassembly. Additionally, avoid using compressed air directly on motors, as this can force debris deeper into sensitive components.
When to Seek Professional Repair
If you've completed all cleaning steps and your Roborock S8 making loud noise continues, the issue may involve internal motor wear, damaged bearings, or a failing suction fan. These repairs require specialized tools and genuine replacement parts. Continuing to run the vacuum with mechanical damage often leads to more expensive failures.
Frequently Asked Questions
Why does my Roborock S8 make a grinding noise only on carpet?
Carpet fibers increase resistance on the main brush, amplifying any existing debris buildup or bearing wear. The brush motor works harder against carpet pile, making minor grinding sounds much more noticeable. Focus on deep-cleaning the main brush bearings and consider replacing the brush if it's worn or deformed from use.
How often should I clean my S8 to prevent loud noises?
For optimal performance, clean the main brush weekly if you have pets or long-haired residents, and bi-weekly for average households. The side brush and front wheel need attention every two weeks. Regular maintenance prevents the debris accumulation that causes most noise issues in the Roborock S8.
Can a software update fix loud noise problems?
Occasionally yes. Firmware updates can optimize motor control algorithms and suction power transitions. However, physical obstructions and wear cannot be resolved through software. Always perform thorough cleaning first, then check for available updates in the Roborock app as a secondary measure.
Still Need Help With Your Roborock Device?
If these steps didn't resolve the making loud noise issue, our certified technicians can help.